|
Leave Your Message
Heavy Oil Burner Preheating Guide: Fuel Viscosity, Temperature, Circulation and Atomization
Technical Guides

Heavy Oil Burner Preheating Guide: Fuel Viscosity, Temperature, Circulation and Atomization

2026-10-17

heavy-oil-burner-preheating-viscosity-temperature-atomization-guide.jpg

Heavy oil burner commissioning often goes wrong when fuel temperature is treated as the target instead of the control variable. The burner does not need an arbitrary “hot” fuel; it needs fuel that reaches the atomizing system within the viscosity and supply conditions required by the burner, fuel grade, and atomization method. Because heavy-fuel viscosity changes strongly with temperature, a setting copied from another plant can produce a very different result.

This matters directly to BAITE heavy-oil applications. The current BAITE heavy-oil range includes burner series with fuel-preheating provisions and air or steam atomization configurations. For a project that spans several series, the useful public reference is the BAITE heavy oil burner range, not a single model presented as universally suitable. The commissioning task is to establish the correct fuel condition for the actual burner and fuel before combustion settings are tuned.

Why Heavy Oil Preheating Is Really a Viscosity-Control Problem

Heating heavy fuel reduces its viscosity and makes it easier to pump and atomize. The temperature-viscosity relationship is therefore central to fuel preparation: changing temperature changes the condition of the oil reaching the atomizer. If that condition varies, droplet formation can vary as well, which changes the way fuel mixes with combustion air and burns.

That is why a preheater setpoint by itself is not enough information. A temperature that is appropriate for one fuel batch, viscosity grade, burner configuration, or atomization system may be wrong for another. The correct commissioning question is:

What fuel viscosity and supply condition does this burner configuration require at the relevant point in the fuel circuit, and what temperature is needed to achieve it with the actual fuel?

Start With Fuel Data Before Adjusting the Preheater

Before changing a thermostat or temperature controller, confirm what fuel is actually being supplied. Heavy fuel descriptions can be too broad for commissioning. Two fuels both described as “heavy oil” can have materially different viscosity-temperature behavior, contamination levels, water content, and handling requirements.

Useful project data includes:

  • the exact fuel grade or supplier specification;
  • viscosity data and the temperature at which that viscosity was measured;
  • the burner and atomization method;
  • the fuel-pump and filtration arrangement;
  • the location of the preheater, temperature sensor, circulation loop, and return line;
  • whether piping or valves require insulation or heat tracing for the selected fuel;
  • the burner firing range and expected operating load.

Use a Fuel-Preparation Sequence Before First Firing

How pre-start fuel checks narrow whether heavy oil is ready for stable delivery and atomization
Check Why it matters What to verify
Fuel identity Different heavy fuels can require different preparation conditions. Fuel grade, supplier data, viscosity reference temperature, and compatibility with the burner.
Preheater control Temperature is used to bring viscosity into the range required by the system. Controller setpoint, sensor location, stable temperature, and any high/low temperature limits specified for the equipment.
Fuel circulation A hot preheater does not prove that the complete fuel path has reached a stable condition. Return flow or circulation arrangement, warm-up time, valve positions, and whether remote piping remains cold.
Filtration and pump supply Restricted or unstable supply can mimic an atomization problem. Filter condition, pump operation, suction conditions, and pressure stability under the required flow.
Atomizing medium Air- or steam-atomized systems depend on more than oil temperature alone. Required atomizing-air or steam conditions and the burner-specific sequence before fuel admission.

Do Not Copy a Universal Heavy-Oil Temperature

There is no defensible single temperature that applies to every heavy oil burner. The practical method is to work backward from the required operating condition:

  1. Confirm the actual fuel and its viscosity data.
  2. Confirm the burner or atomizer's permitted fuel condition from the applicable documentation.
  3. Use the fuel's viscosity-temperature relationship to determine the needed temperature range.
  4. Verify that the installed preheater and circulation arrangement can reach and hold that condition at the required fuel flow.
  5. Confirm the condition under operating flow, not only during static warm-up.

Atomization Method Changes What Must Be Verified

Heavy-oil burners do not all atomize fuel in the same way. BAITE's current BT10-20HAE and BT30-60HAE product pages, for example, specify air or steam atomization and include fuel preheaters with temperature indication and adjustable temperature control.

Separate Fuel-Preparation Problems From Combustion-Adjustment Problems

Observed condition Possible fuel-preparation relevance Next verification
Fuel temperature keeps drifting Fuel viscosity at the atomizer may also be changing. Preheater capacity, controller response, sensor location, circulation, and actual fuel flow.
Pressure becomes unstable as firing rate rises Viscosity, filter restriction, pump supply, or line losses may be affecting delivery. Pressure under operating flow, filter condition, suction conditions, and fuel temperature at the relevant point.
Ignition is poor or the flame is unstable Fuel condition can contribute, but ignition, atomizing medium, air settings, and furnace conditions can also be involved. Confirm fuel preparation first, then follow the burner commissioning and flame-safeguard sequence.
Smoke or carbon deposits appear Poor atomization can be one cause, but insufficient air or furnace/flue conditions can produce similar evidence. Use measured fuel and combustion conditions rather than changing only the preheater or air setting.

A Practical Commissioning Order for Heavy-Oil Fuel Preparation

  1. Confirm the burner configuration.
  2. Confirm the fuel.
  3. Prepare the fuel circuit.
  4. Establish stable temperature and flow.
  5. Verify the atomizing medium.
  6. Proceed with the burner sequence.
  7. Commission combustion only after fuel preparation is stable.

Request Heavy Oil Burner Selection Support

Provide the fuel grade and viscosity data, boiler or furnace type, required heat input, expected firing range, atomizing-air or steam conditions where applicable, fuel-supply arrangement, electrical supply, and project requirements. BAITE can then review the relevant heavy-oil burner configuration and fuel-preparation needs. Request Burner Selection Support.

Frequently Asked Questions

What temperature should heavy oil be heated to before the burner starts?

There is no universal temperature for every heavy oil burner. The required temperature depends on the actual fuel's viscosity-temperature relationship, the burner or atomizer's permitted fuel condition, and the fuel-system arrangement.

Why is viscosity more useful than temperature alone?

Temperature is one of the main variables used to change heavy-oil viscosity, but the burner ultimately receives fuel with a particular flow and atomization behavior. Two fuels at the same temperature can have different viscosities.

Does a stable preheater temperature mean the heavy oil is ready to fire?

Not by itself. The fuel path also needs stable circulation and supply conditions, and the relevant downstream fuel condition must match the burner requirement.

Can I raise the preheater temperature to fix black smoke?

Do not assume black smoke is caused only by fuel temperature. Confirm the actual fuel condition first, then investigate the complete fuel-air-furnace relationship using appropriate measurements.

What information does BAITE need to select a heavy oil burner?

Useful inputs include the fuel grade and viscosity data, boiler or furnace type, required burner capacity or heat input, expected firing range, combustion-chamber and operating conditions, and atomizing-air or steam availability.